Roll-N-Lock A-Series XT Won’t Lock Closed? Here’s the Fix

If your A-Series XT canister won’t stay locked and pops open every time you try to secure it, you’re likely dealing with a misaligned striker plate — a common issue after months of use or a hard jolt on rough terrain. The good news is that this fix takes about ten minutes and requires only a wrench and a flashlight.

We’re walking you through exactly what causes the locking mechanism to fail and how to realign the striker plate so your cover locks tight every time.

Roll-N-Lock A-Series XT Won't Lock Closed? Here's the Fix

Why the A-Series XT Latch Fails to Engage

The A-Series XT uses a spring-loaded latch on the canister that hooks into a striker plate mounted to the truck bed rail. When you close the cover, the latch should snap into the striker and hold the canister down against compression from the internal spring.

If the striker plate shifts even a quarter inch forward or backward, the latch misses its catch point and slides past instead of engaging. This happens most often after installation on a truck with a spray-in bedliner — the liner’s texture prevents the mounting hardware from sitting completely flush, and vibration over time nudges the plate out of position.

You’ll know the striker is off if the canister bounces open as soon as you release pressure, or if you hear the latch click but the cover still pops up. According to the working principle of mechanical latches, proper engagement requires the catch surface and the bolt to align within a narrow tolerance — usually less than 3 mm for automotive applications.


Tools and Materials You’ll Need

Grab a 10 mm socket wrench or adjustable wrench, a flathead screwdriver, and a flashlight or headlamp. The striker plate is held by two hex bolts underneath the bed rail, and they can be hard to see without direct light.

You won’t need any replacement hardware unless the striker plate itself is cracked or the bolts are stripped. Most alignment problems are solved by loosening, shifting, and retightening the existing plate.


Step-by-Step Striker Plate Adjustment

Step 1: Locate the Striker Plate

Open the A-Series XT canister fully and look at the bed rail near the cab. The striker plate is a small metal piece bolted to the inside edge of the rail, positioned to catch the latch when the cover closes.

Step 2: Loosen the Mounting Bolts

Use your wrench to loosen — but do not remove — the two hex bolts that secure the striker plate. You want the plate to stay in place but be able to slide a few millimeters in any direction.

Step 3: Test the Latch Position

With the bolts loose, gently close the canister and watch where the latch contacts the striker plate. If the latch is hitting above, below, or to one side of the catch surface, slide the plate until the latch hooks cleanly into the center of the striker.

Hold the plate in that position and open the canister again without letting the plate shift. If you’re working alone, a small piece of tape can hold the plate steady while you tighten the bolts.

Step 4: Tighten and Test

Tighten both bolts firmly, making sure the striker plate doesn’t rotate or shift as you apply torque. Close the canister and press down — it should lock with an audible click and stay closed when you release pressure.

If the cover still pops open, loosen the bolts again and shift the plate another millimeter or two in the direction the latch is pulling. Repeat until the lock engages cleanly every time.

Step-by-Step Striker Plate Adjustment

What to Do If Adjustment Doesn’t Solve It

If realigning the striker plate doesn’t fix the problem, inspect the latch mechanism on the canister itself. Look for a broken spring, a bent latch arm, or debris stuck in the pivot point.

The internal spring that keeps tension on the latch can weaken over time, especially in extreme heat. If the spring feels loose or the latch doesn’t snap back into position when you press it, you may need to replace the latch assembly rather than adjust the striker.

Owners troubleshooting similar retraction issues on the E-Series model have found that cleaning the canister track and re-lubricating the slats often resolves binding that mimics a latch problem — worth checking if your XT canister also feels sluggish when opening.


Keep Your A-Series XT Locking Smoothly

A misaligned striker plate is the single most common reason an A-Series XT won’t lock, and it’s also one of the easiest fixes once you know where to look. Spending ten minutes with a wrench now will save you from wrestling with a cover that pops open every time you try to secure it.

If you’ve adjusted the striker and the latch still won’t engage, inspect the latch mechanism itself for wear or damage — and don’t hesitate to replace the hardware before a small problem turns into a stuck canister or a bent rail. We built the XT to last, and keeping the locking system aligned is all it takes to make sure it does.


Good to know

Common Questions About A-Series XT Locking Issues

Close the canister slowly and watch where the latch makes contact. If the latch is hitting the striker but sliding off instead of hooking, the striker position is the issue.

If the latch doesn’t extend far enough to reach the striker at all, or if it feels loose and wobbly, the latch mechanism or its internal spring has failed and needs replacement.

Yes, a small amount of medium-strength thread locker on the bolts will help prevent the striker from shifting again after you’ve aligned it. Make sure the plate is locked in the correct position before the compound sets.

Avoid high-strength formulas — you want to be able to readjust the plate in the future if needed without heating the bolts.

Repeated failed engagement can bend the latch arm or wear down the striker plate’s catch surface, especially if you’re forcing the canister closed. Once you notice the lock isn’t catching cleanly, adjust the striker right away to avoid permanent damage to either component.

Yes, both models use the same bed-rail mounting system. If you’re switching between the two or looking at installation notes, the striker hardware and adjustment process are identical.

Stripped bolts need to be replaced immediately — a loose striker will continue to shift and make locking impossible. Most hardware stores carry M6 or M8 hex bolts that match the original threading, or you can order OEM replacements if the bed rail threads are also damaged.

Yes, you don’t need to remove the entire tonneau cover. Just open the canister fully so you can access the bed rail and the striker plate bolts from inside the truck bed.